Barracuda Control Server
Barracuda Control Server - Quick Start Guide
The Barracuda Control Server enables administrators to monitor and configure
multiple Barracuda Networks products from a single console. Through the web
interface, you can check the health of all connected devices, run reports that are
generated by gathering data from all the devices, and assign roles with varied
permissions to different types of users.
Getting Started
This guide provides you with setup instructions for the Barracuda Control
Server. We recommend reading these instructions fully before starting the
setup. To begin setting up your Barracuda Control Server, you need the
following:
Barracuda Control Server, AC power cord, Ethernet cables (included)
VGA monitor (recommended)
USB keyboard (recommended)
Physical Installation
To install the Barracuda Control Server:
1. Fasten the Barracuda Control Server to a 19-inch rack or place it in a
stable location.
2. Connect a CAT5 or CAT6 Ethernet cable from your network switch to the
Ethernet port on the back of the Barracuda Control Server.
3. Connect a standard VGA monitor, USB keyboard, and an AC power cord
to the Barracuda Control Server. Note: Immediately after connecting an
AC power cord to the unit, it may power ON for a few seconds and then
power OFF. This is because the unit is designed to automatically return to
a powered ON state in the event of a power outage.
4. Press the POWER button on the front panel to turn the unit on.
Configure IP Address and Network Settings
If you have a monitor connected, the Barracuda Control Server initially
displays the Boot Menu; once fully booted, the Administrative Console login
prompt displays. To begin the configuration, log in using the Barracuda Control
Server Administrator Account:
1. Log in to the Administrative Console using the admin login admin/admin.
2. Configure the IP Address, Subnet Mask, Default Gateway, Primary DNS
Server, and Secondary DNS Server as appropriate for your network.
3. Save your changes.
If you do not have a monitor and keyboard, you can set the IP using the
RESET button on the front panel. Press and hold the RESET button per the
following table:
IP address Press and hold RESET for…
192.168.200.200 5 seconds
192.168.1.200 8 seconds
10.1.1.200 12 seconds
Note: Barracuda devices you wish to manage through the Barracuda Control
Server must have a network path between the two devices and at least one of
the following ports available to communicate between the devices: port 80,
8000, 23557, or 48320.
Open Firewall Ports
If your Barracuda Control Server is located behind a corporate firewall, you
may need to open ports 1194 and ports 5120-5129 outbound for both TCP and
UDP to allow communication between the Barracuda Control Server and the
Internet.
These ports are used to transfer data either to the Barracuda Control Server or
to another Barracuda Networks appliance over the Internet. To restrict
outbound network traffic on these ports, contact Barracuda Networks
Technical Support for a list of the IP addresses to allow.
Verify and Configure Access from the Web Interface
Use a computer with a web browser connected to the same network as the
Barracuda Control Server, and follow these steps:
1. In the browser address bar, enter http:// followed by the Barracuda Control
Server IP address, followed by the default Web Interface HTTP Port
(:8000). For example, if you configured the Barracuda Control Server
with an IP address of 192.168.200.200, you would enter the following:
http://192.168.200.200:8000
2. Log in to the Barracuda Control Server web interface using the Barracuda
Control Server Administrator Account, admin/admin.
3. Go to the CLOUD CONTROL > IP Configuration page, and perform the
following steps:
Verify the values for IP Address, Subnet Mask, and Default Gateway.
Verify the values for Primary and Secondary DNS Server.
You can optionally enter the Proxy Server details.
Enter the Default Domain. For example, <yourdomainname>.com.
4. Click any of the Save Changes buttons to save the entered information.
(49 strony)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji